# Boots from emmc flashed with SD rk3399-eflasher-buildroot-20230314.img.gz

DDR Version 1.24 20191016
In
Channel 0: DDR3, 800MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
no stride
ch 0 ddrconfig = 0x101, ddrsize = 0x20
pmugrf_os_reg[2] = 0x10006281, stride = 0x17
OUT
Boot1 Release Time: May 29 2020 17:36:36, version: 1.26
CPUId = 0x0
ChipType = 0x10, 338
SdmmcInit=2 0
BootCapSize=100000
UserCapSize=14910MB
FwPartOffset=2000 , 100000
mmc0:cmd5,20
SdmmcInit=0 0
BootCapSize=0
UserCapSize=123135MB
FwPartOffset=0 , 0
StorageInit ok = 1164702
SecureMode = 0
SecureInit read PBA: 0x4
SecureInit read PBA: 0x404
SecureInit read PBA: 0x804
SecureInit read PBA: 0xc04
SecureInit read PBA: 0x1004
SecureInit read PBA: 0x1404
SecureInit read PBA: 0x1804
SecureInit read PBA: 0x1c04
SecureInit ret = 0, SecureMode = 0
atags_set_bootdev: ret:(0)
GPT part:  0, name:            uboot, start:0x4000, size:0x2000
GPT part:  1, name:            trust, start:0x6000, size:0x2000
GPT part:  2, name:             misc, start:0x8000, size:0x2000
GPT part:  3, name:             dtbo, start:0xa000, size:0x2000
GPT part:  4, name:         resource, start:0xc000, size:0x8000
GPT part:  5, name:           kernel, start:0x14000, size:0x14000
GPT part:  6, name:             boot, start:0x28000, size:0x18000
GPT part:  7, name:           rootfs, start:0x40000, size:0x11e000
GPT part:  8, name:         userdata, start:0x15e000, size:0x1bc0fdf
find part:uboot OK. first_lba:0x4000.
find part:trust OK. first_lba:0x6000.
Trust Addr:0x6000, 0x58334c42
No find bl30.bin
Load uboot, ReadLba = 4000
Load OK, addr=0x200000, size=0xf9190
RunBL31 0x40000 @ 1206343 us
NOTICE:  BL31: v1.3(release):845ee93
NOTICE:  BL31: Built : 15:51:11, Jul 22 2020
NOTICE:  BL31: Rockchip release version: v1.1
INFO:    GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 0
INFO:    plat_rockchip_pmu_init(1196): pd status 3e
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
INF [0x0] TEE-CORE:init_primary_helper:337: Initializing (1.1.0-256-gebb61ff5 #4 Wed Apr 22 01:34:02 UTC 2020 aarch64)

INF [0x0] TEE-CORE:init_primary_helper:338: Release version: 1.2

INF [0x0] TEE-CORE:init_teecore:83: teecore inits done
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


U-Boot 2017.09-g60a32b8360 # (Aug 19 2022 - 16:43:10 +0800)

Board: FriendlyELEC RK3399 board
PreSerial: 2
DRAM:  992 MiB
Sysmem: init
Relocation Offset: 3dbca000, fdt: 3bdbe3f8
Using default environment

mmc@fe320000: 1, sdhci@fe330000: 0
Bootdev(atags): mmc 0
MMC0: HS400, 150Mhz
PartType: EFI
boot mode: None
Found DTB in resource part
DTB: rk3399-nanopi4-rev04.dtb (107593)
HASH(c): OK
ANDROID: fdt overlay OK
I2c0 speed: 400000Hz
PMIC:  RK808 
vdd_center 900000 uV
vdd_cpu_l 900000 uV
vccio_sd init 3000000 uV
vdd_log 900000 uV
I2c2 speed: 100000Hz
Rockchip UBOOT DRM driver version: v1.0.1
I2c7 speed: 100000Hz
Monitor has basic audio support
Could not find baseparameter partition
mode: 1920x1080
Non-CEA mode used in HDMI
final pixclk = 148500000 tmdsclk = 148500000
PHY powered down in 0 iterations
PHY PLL locked 1 iterations
PHY powered down in 0 iterations
PHY PLL locked 1 iterations
sink has audio support
hdmi_set_clk_regenerator: fs=48000Hz ftdms=148.500MHz N=6144 cts=148500
AUX CH error happens: 2
AUX CH error happens: 2
AUX CH error happens: 2
AUX CH error happens: 2
AUX CH error happens: 2
AUX CH error happens: 2
AUX CH error happens: 2
AUX CH error happens: 2
AUX CH error happens: 2
failed to get edid
failed to find display timing
CLK: (uboot. arml: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
CLK: (uboot. armb: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
  aplll 816000 KHz
  apllb 816000 KHz
  dpll 800000 KHz
  cpll 24000 KHz
  gpll 800000 KHz
  npll 600000 KHz
  vpll 148000 KHz
  aclk_perihp 133333 KHz
  hclk_perihp 66666 KHz
  pclk_perihp 33333 KHz
  aclk_perilp0 266666 KHz
  hclk_perilp0 88888 KHz
  pclk_perilp0 44444 KHz
  hclk_perilp1 100000 KHz
  pclk_perilp1 50000 KHz

Net:   eth0: ethernet@fe300000
Hit key to stop autoboot('CTRL+C'):  0 
Device 'mmc@fe310000': seq 0 is in use by 'sdhci@fe330000'
Card did not respond to voltage select!
mmc_init: -95, time 47
Could not get mmc 0

## Booting Rockchip Format Image
fdt	 @ 0x08300000 (0x0001a6e4)
kernel   @ 0x00280000 (0x01f21808)
ramdisk  @ 0x0a200000 (0x007233c0)
Fdt Ramdisk skip relocation
## Flattened Device Tree blob at 08300000
   Booting using the fdt blob at 0x8300000
  'reserved-memory' ramoops@110000: addr=110000 size=f0000
   Using Device Tree in place at 0000000008300000, end 000000000831d6e3
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x0a200000 - 0x40000000 (size: 0x35e00000)
Total: 1919.730 ms

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 4.19.193 (ubuntu@6037d27d53a9) (gcc version 6.4.0 (ctng-1.23.0-150g-FA), GNU ld (ctng-1.23.0-150g-FA) 2.28) #1 SMP PREEMPT Fri Aug 19 16:48:03 CST 2022
[    0.000000] Machine model: FriendlyElec NanoPi NEO4
[    0.000000] earlycon: uart8250 at MMIO32 0x00000000ff1a0000 (options '')
[    0.000000] bootconsole [uart8250] enabled
[    0.000000] Panel: using mode 1920x1080 for HDMI1920x1080
[    0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'stb-devinfo@00000000': base 0x0000000000000000, size 0 MiB
[    0.000000] cma: Reserved 16 MiB at 0x000000003f000000
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: Trusted OS migration not required
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] percpu: Embedded 24 pages/cpu s60264 r8192 d29848 u98304
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 249864
[    0.000000] Kernel command line: storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal androidboot.dtbo_idx=0 earlycon=uart8250,mmio32,0xff1a0000 swiotlb=1 coherent_pool=1m rw console=ttyFIQ0 root=/dev/mmcblk2p8 rootfstype=ext4 data=/dev/mmcblk2p9 consoleblank=0 cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1 lcd=HDMI1920x1080
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 935536K/1015808K available (14462K kernel code, 2118K rwdata, 4524K rodata, 10752K init, 2147K bss, 63888K reserved, 16384K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[    0.000000] ftrace: allocating 47978 entries in 188 pages
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu: 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
[    0.000000] 	Tasks RCU enabled.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[    0.000000] GICv3: Distributor has no Range Selector support
[    0.000000] GICv3: no VLPI support, no direct LPI support
[    0.000000] ITS [mem 0xfee20000-0xfee3ffff]
[    0.000000] ITS@0x00000000fee20000: allocated 65536 Devices @3e580000 (flat, esz 8, psz 64K, shr 0)
[    0.000000] ITS: using cache flushing for cmd queue
[    0.000000] GIC: using LPI property table @0x000000003e560000
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fef00000
[    0.000000] CPU0: using LPI pending table @0x000000003e570000
[    0.000000] GIC: using cache flushing for LPI property table
[    0.000000] GICv3: GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
[    0.000000] GICv3: GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
[    0.000000] random: random: get_random_bytes called from start_kernel+0x378/0x4fc with crng_init=0
[    0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop0_frac as parent of dclk_vop0, rate changes may not work
[    0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop1_frac as parent of dclk_vop1, rate changes may not work
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.002113] Console: colour dummy device 80x25
[    0.002575] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[    0.003535] pid_max: default: 32768 minimum: 301
[    0.004123] Security Framework initialized
[    0.004516] AppArmor: AppArmor disabled by boot time parameter
[    0.005117] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[    0.005768] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[    0.008478] ASID allocator initialised with 32768 entries
[    0.009160] rcu: Hierarchical SRCU implementation.
[    0.012175] Platform MSI: interrupt-controller@fee20000 domain created
[    0.013345] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[    0.015094] smp: Bringing up secondary CPUs ...
[    0.016233] Detected VIPT I-cache on CPU1
[    0.016267] GICv3: CPU1: found redistributor 1 region 0:0x00000000fef20000
[    0.016312] CPU1: using LPI pending table @0x000000003e7b0000
[    0.016362] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.017152] Detected VIPT I-cache on CPU2
[    0.017177] GICv3: CPU2: found redistributor 2 region 0:0x00000000fef40000
[    0.017216] CPU2: using LPI pending table @0x000000003e7d0000
[    0.017252] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.018008] Detected VIPT I-cache on CPU3
[    0.018033] GICv3: CPU3: found redistributor 3 region 0:0x00000000fef60000
[    0.018070] CPU3: using LPI pending table @0x000000003e7f0000
[    0.018105] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.018878] ARM_SMCCC_ARCH_WORKAROUND_1 missing from firmware
[    0.018885] CPU features: enabling workaround for EL2 vector hardening
[    0.018894] Detected PIPT I-cache on CPU4
[    0.018921] GICv3: CPU4: found redistributor 100 region 0:0x00000000fef80000
[    0.018975] CPU4: using LPI pending table @0x000000003c440000
[    0.019010] CPU4: Booted secondary processor 0x0000000100 [0x410fd082]
[    0.019833] Detected PIPT I-cache on CPU5
[    0.019856] GICv3: CPU5: found redistributor 101 region 0:0x00000000fefa0000
[    0.019906] CPU5: using LPI pending table @0x000000003c450000
[    0.019936] CPU5: Booted secondary processor 0x0000000101 [0x410fd082]
[    0.020056] smp: Brought up 1 node, 6 CPUs
[    0.032422] SMP: Total of 6 processors activated.
[    0.032866] CPU features: detected: GIC system register CPU interface
[    0.033470] CPU features: detected: 32-bit EL0 Support
[    0.041254] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[    0.042036] CPU: All CPU(s) started at EL2
[    0.042461] alternatives: patching kernel code
[    0.044551] devtmpfs: initialized
[    0.060857] Trying to unpack rootfs image as initramfs...
[    0.061384] Registered cp15_barrier emulation handler
[    0.061886] Registered setend emulation handler
[    0.062731] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.063668] futex hash table entries: 2048 (order: 5, 131072 bytes)
[    0.064755] pinctrl core: initialized pinctrl subsystem
[    0.066207] NET: Registered protocol family 16
[    0.067172] schedtune: configured to support 6 boost groups
[    0.067950] audit: initializing netlink subsys (disabled)
[    0.069824] cpuidle: using governor menu
[    0.070220] Registered FIQ tty driver
[    0.070946] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.071628] audit: type=2000 audit(0.066:1): state=initialized audit_enabled=0 res=1
[    0.083902] DMA: preallocated 1024 KiB pool for atomic allocations
[    0.086763] console [pstore-1] enabled
[    0.087291] pstore: Registered ramoops as persistent store backend
[    0.087887] ramoops: attached 0xf0000@0x110000, ecc: 0/0
[    0.114627] rockchip-gpio ff720000.gpio0: probed gpio0 (ff720000.gpio0)
[    0.115703] rockchip-gpio ff730000.gpio1: probed gpio1 (ff730000.gpio1)
[    0.116803] rockchip-gpio ff780000.gpio2: probed gpio2 (ff780000.gpio2)
[    0.117986] rockchip-gpio ff788000.gpio3: probed gpio3 (ff788000.gpio3)
[    0.119090] rockchip-gpio ff790000.gpio4: probed gpio4 (ff790000.gpio4)
[    0.119876] rockchip-pinctrl pinctrl: probed pinctrl
[    0.129669] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.133717] cryptd: max_cpu_qlen set to 1000
[    0.136452] fiq debugger fiq mode enabled
[[    0.137230] console [ttyFIQ0] enabled
    0.137230] console [ttyFIQ0] enabled
[    0.137936] bootconsole [uart8250] disabled
[    0.137936] bootconsole [uart8250] disabled
[    0.138542] Registered fiq debugger ttyFIQ0
[    0.167258] vcc_lcd: supplied by vcc5v0_sys
[    0.167955] rk_iommu ff650800.iommu: version = 1
[    0.168443] rk_iommu ff660480.iommu: version = 1
[    0.168817] rk_iommu ff670800.iommu: version = 1
[    0.169182] rk_iommu ff8f3f00.iommu: version = 1
[    0.169447] rk_iommu ff903f00.iommu: version = 1
[    0.169710] rk_iommu ff914000.iommu: version = 1
[    0.170057] rk_iommu ff924000.iommu: version = 1
[    0.170701] SCSI subsystem initialized
[    0.170899] usbcore: registered new interface driver usbfs
[    0.170940] usbcore: registered new interface driver hub
[    0.170987] usbcore: registered new device driver usb
[    0.171312] media: Linux media interface: v0.10
[    0.171341] videodev: Linux video capture interface: v2.00
[    0.171417] pps_core: LinuxPPS API ver. 1 registered
[    0.171427] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.171445] PTP clock support registered
[    0.173788] Advanced Linux Sound Architecture Driver Initialized.
[    0.174204] Bluetooth: Core ver 2.22
[    0.174249] NET: Registered protocol family 31
[    0.174264] Bluetooth: HCI device and connection manager initialized
[    0.174278] Bluetooth: HCI socket layer initialized
[    0.174294] Bluetooth: L2CAP socket layer initialized
[    0.174356] Bluetooth: SCO socket layer initialized
[    0.174380] NetLabel: Initializing
[    0.174395] NetLabel:  domain hash size = 128
[    0.174404] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.174462] NetLabel:  unlabeled traffic allowed by default
[    0.174957] rockchip-cpuinfo cpuinfo: SoC		: 0
[    0.174977] rockchip-cpuinfo cpuinfo: Serial		: 3293b0852c213abe
[    0.175609] clocksource: Switched to clocksource arch_sys_counter
[    0.225318] VFS: Disk quotas dquot_6.6.0
[    0.225394] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.225518] FS-Cache: Loaded
[    0.234764] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[    0.235795] NET: Registered protocol family 2
[    0.236488] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 20480 bytes)
[    0.236537] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.236615] TCP bind hash table entries: 8192 (order: 6, 262144 bytes)
[    0.236813] TCP: Hash tables configured (established 8192 bind 8192)
[    0.236940] UDP hash table entries: 512 (order: 3, 49152 bytes)
[    0.237003] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes)
[    0.237203] NET: Registered protocol family 1
[    0.237686] RPC: Registered named UNIX socket transport module.
[    0.237705] RPC: Registered udp transport module.
[    0.237715] RPC: Registered tcp transport module.
[    0.237728] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.239777] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[    0.240148] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
[    0.241950] Initialise system trusted keyrings
[    0.242146] workingset: timestamp_bits=45 max_order=18 bucket_order=0
[    0.248487] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.248856] Registering sdcardfs 0.1
[    0.249135] FS-Cache: Netfs 'nfs' registered for caching
[    0.249593] NFS: Registering the id_resolver key type
[    0.249624] Key type id_resolver registered
[    0.249638] Key type id_legacy registered
[    0.249655] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.249674] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[    0.249877] fuse init (API version 7.27)
[    0.250471] 
[    0.250471] TEE Core Framework initialization (ver 1:0.1)
[    0.250498] TEE armv7 Driver initialization
[    0.250974] tz_tee_probe: name="armv7sec", id=0, pdev_name="armv7sec.0"
[    0.250990] TEE core: Alloc the misc device "opteearmtz00" (id=0)
[    0.251169] TEE Core: Register the misc device "opteearmtz00" (id=0,minor=62)
[    0.252451] Key type asymmetric registered
[    0.252466] Asymmetric key parser 'x509' registered
[    0.252508] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[    0.252675] io scheduler noop registered
[    0.252879] io scheduler cfq registered (default)
[    0.252897] io scheduler mq-deadline registered
[    0.252907] io scheduler kyber registered
[    0.253013] io scheduler bfq registered
[    0.255167] phy phy-ff770000.syscon:usb2-phy@e460.1: Linked as a consumer to regulator.2
[    0.255644] phy phy-ff770000.syscon:usb2-phy@e460.2: No vbus specified for otg port
[    0.257218] rockchip-mipi-dphy-rx ff770000.syscon:mipi-dphy-rx0: invalid resource
[    0.261839] rockchip-pcie f8000000.pcie: missing "memory-region" property
[    0.262015] rockchip-pcie f8000000.pcie: no vpcie12v regulator found
[    0.262044] rockchip-pcie f8000000.pcie: no vpcie3v3 regulator found
[    0.262069] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found
[    0.262094] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found
[    0.262126] rockchip-pcie f8000000.pcie: host bridge /pcie@f8000000 ranges:
[    0.262156] rockchip-pcie f8000000.pcie:   MEM 0xfa000000..0xfbdfffff -> 0xfa000000
[    0.262173] rockchip-pcie f8000000.pcie:    IO 0xfbe00000..0xfbefffff -> 0xfbe00000
[    0.432890] Freeing initrd memory: 7308K
[    0.785677] rockchip-pcie f8000000.pcie: PCIe link training gen1 timeout!
[    0.785715] rockchip-pcie f8000000.pcie: deferred probe failed
[    0.785843] rockchip-pcie: probe of f8000000.pcie failed with error -110
[    0.786826] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    0.786906] pwm-backlight backlight: Linked as a consumer to regulator.0
[    0.787278] iommu: Adding device ff670000.iep to group 2
[    0.787312] iep ff670000.iep: Linked as a consumer to ff670800.iommu
[    0.787526] iep: failed to find iep power down clock source.
[    0.787991] iep: IEP Power ON
[    0.788046] iep: IEP Power OFF
[    0.788138] iep: IEP Driver loaded succesfully
[    0.788384] iep: Module initialized.
[    0.788610] mpp_service mpp-srv: eccf16e83556 author: Finley Xiao 2021-07-05 soc: rockchip: opp_select: Export rockchip_nvmem_cell_read_u8/u16()
[    0.788677] mpp_service mpp-srv: probe start
[    0.789210] iommu: Adding device ff660000.rkvdec to group 1
[    0.789244] mpp_rkvdec ff660000.rkvdec: Linked as a consumer to ff660480.iommu
[    0.789464] mpp_rkvdec ff660000.rkvdec: probing start
[    0.789961] rkvdec_init:1219: failed on clk_get clk_hevc_cabac
[    0.790058] mpp_rkvdec ff660000.rkvdec: shared_video_hevc_cabac is not found!
[    0.790084] rkvdec_init:1250: No hevc cabac reset resource define
[    0.790367] mpp_rkvdec ff660000.rkvdec: probing finish
[    0.791623] iommu: Adding device ff650400.vdpu to group 0
[    0.791648] mpp_vdpu2 ff650400.vdpu: Linked as a consumer to ff650800.iommu
[    0.791843] mpp_vdpu2 ff650400.vdpu: probe device
[    0.792245] mpp_vdpu2 ff650400.vdpu: reset_group->rw_sem_on=0
[    0.792295] mpp_vdpu2 ff650400.vdpu: reset_group->rw_sem_on=0
[    0.792485] mpp_vdpu2 ff650400.vdpu: probing finish
[    0.792913] iommu: Adding device ff650000.vepu to group 0
[    0.792949] mpp_vepu2 ff650000.vepu: Linked as a consumer to ff650800.iommu
[    0.793004] mpp_vepu2 ff650000.vepu: probe device
[    0.793389] mpp_vepu2 ff650000.vepu: reset_group->rw_sem_on=0
[    0.793426] mpp_vepu2 ff650000.vepu: reset_group->rw_sem_on=0
[    0.793590] mpp_vepu2 ff650000.vepu: probing finish
[    0.794520] mpp_service mpp-srv: probe success
[    0.798246] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.798270] dma-pl330 ff6d0000.dma-controller: 	DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
[    0.799543] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.799565] dma-pl330 ff6e0000.dma-controller: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[    0.800944] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[    0.801564] vdd_log: supplied by regulator-dummy
[    0.802098] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[    0.802766] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 40, base_baud = 1500000) is a 16550A
[    0.803327] ff370000.serial: ttyS4 at MMIO 0xff370000 (irq = 42, base_baud = 1500000) is a 16550A
[    0.805816] random: fast init done
[    0.806081] iommu: Adding device ff8f0000.vop to group 3
[    0.806116] rockchip-vop ff8f0000.vop: Linked as a consumer to ff8f3f00.iommu
[    0.806141] random: crng init done
[    0.806532] iommu: Adding device ff900000.vop to group 4
[    0.806566] rockchip-vop ff900000.vop: Linked as a consumer to ff903f00.iommu
[    0.810775] rockchip-drm display-subsystem: Linked as a consumer to ff8f0000.vop
[    0.810812] rockchip-drm display-subsystem: Linked as a consumer to ff900000.vop
[    0.811755] rockchip-drm display-subsystem: Linked as a consumer to ff970000.edp
[    0.811892] rockchip-drm display-subsystem: Linked as a consumer to fec00000.dp
[    0.812340] rockchip-drm display-subsystem: Linked as a consumer to ff940000.hdmi
[    0.815574] panel-friendlyelec edp-panel: Linked as a consumer to regulator.6
[    0.818029] midgard ff9a0000.gpu: Failed to get regulator
[    0.818048] midgard ff9a0000.gpu: Power control initialization failed
[    0.818406] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    0.822420] brd: module loaded
[    0.830442] loop: module loaded
[    0.832694] libphy: Fixed MDIO Bus: probed
[    0.833530] rk_gmac-dwmac fe300000.ethernet: PTP uses main clock
[    0.833627] rk_gmac-dwmac fe300000.ethernet: Linked as a consumer to regulator.5
[    0.833647] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
[    0.833668] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
[    0.833683] rk_gmac-dwmac fe300000.ethernet: RX delay(0x11).
[    0.833703] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
[    0.833764] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
[    0.833779] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
[    0.838796] rk_gmac-dwmac fe300000.ethernet: init for RGMII
[    0.839019] rk_gmac-dwmac fe300000.ethernet: User ID: 0x10, Synopsys ID: 0x35
[    0.839040] rk_gmac-dwmac fe300000.ethernet: 	DWMAC1000
[    0.839053] rk_gmac-dwmac fe300000.ethernet: DMA HW capability register supported
[    0.839067] rk_gmac-dwmac fe300000.ethernet: RX Checksum Offload Engine supported
[    0.839078] rk_gmac-dwmac fe300000.ethernet: COE Type 2
[    0.839090] rk_gmac-dwmac fe300000.ethernet: TX Checksum insertion supported
[    0.839103] rk_gmac-dwmac fe300000.ethernet: Wake-Up On Lan supported
[    0.839138] rk_gmac-dwmac fe300000.ethernet: Normal descriptors
[    0.839153] rk_gmac-dwmac fe300000.ethernet: Ring mode enabled
[    0.839164] rk_gmac-dwmac fe300000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    0.930754] libphy: stmmac: probed
[    0.930785] RTL8211E Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211E Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[    0.930798] RTL8211E Gigabit Ethernet stmmac-0:01: attached PHY driver [RTL8211E Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
[    0.932315] PPP generic driver version 2.4.2
[    0.932556] usbcore: registered new interface driver asix
[    0.932628] usbcore: registered new interface driver ax88179_178a
[    0.932681] usbcore: registered new interface driver cdc_ether
[    0.932736] usbcore: registered new interface driver rndis_host
[    0.932815] usbcore: registered new interface driver qmi_wwan
[    0.934065] dwc3 fe800000.dwc3: Failed to get clk 'ref': -2
[    0.935215] dwc3 fe900000.dwc3: Failed to get clk 'ref': -2
[    0.940461] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.940495] ehci-pci: EHCI PCI platform driver
[    0.940569] ehci-platform: EHCI generic platform driver
[    0.942965] ehci-platform fe3c0000.usb: EHCI Host Controller
[    0.942999] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 1
[    0.943291] ehci-platform fe3c0000.usb: irq 33, io mem 0xfe3c0000
[    0.955642] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
[    0.955860] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[    0.955881] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.955900] usb usb1: Product: EHCI Host Controller
[    0.955916] usb usb1: Manufacturer: Linux 4.19.193 ehci_hcd
[    0.955931] usb usb1: SerialNumber: fe3c0000.usb
[    0.956394] hub 1-0:1.0: USB hub found
[    0.956441] hub 1-0:1.0: 1 port detected
[    0.957096] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.957127] ohci-platform: OHCI generic platform driver
[    0.957512] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
[    0.957548] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 2
[    0.957790] ohci-platform fe3e0000.usb: irq 34, io mem 0xfe3e0000
[    1.016454] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[    1.016476] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.016488] usb usb2: Product: Generic Platform OHCI controller
[    1.016499] usb usb2: Manufacturer: Linux 4.19.193 ohci_hcd
[    1.016509] usb usb2: SerialNumber: fe3e0000.usb
[    1.016951] hub 2-0:1.0: USB hub found
[    1.017040] hub 2-0:1.0: 1 port detected
[    1.018541] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    1.018582] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[    1.019230] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000009002030010
[    1.019286] xhci-hcd xhci-hcd.1.auto: irq 75, io mem 0xfe900000
[    1.019627] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[    1.019647] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.019666] usb usb3: Product: xHCI Host Controller
[    1.019681] usb usb3: Manufacturer: Linux 4.19.193 xhci-hcd
[    1.019696] usb usb3: SerialNumber: xhci-hcd.1.auto
[    1.020159] hub 3-0:1.0: USB hub found
[    1.020248] hub 3-0:1.0: 1 port detected
[    1.020587] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    1.020623] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[    1.020655] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[    1.020769] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    1.020905] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.19
[    1.020955] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.020980] usb usb4: Product: xHCI Host Controller
[    1.021003] usb usb4: Manufacturer: Linux 4.19.193 xhci-hcd
[    1.021027] usb usb4: SerialNumber: xhci-hcd.1.auto
[    1.021480] hub 4-0:1.0: USB hub found
[    1.021535] hub 4-0:1.0: 1 port detected
[    1.022003] usbcore: registered new interface driver cdc_acm
[    1.022029] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.022085] usbcore: registered new interface driver cdc_wdm
[    1.022354] usbcore: registered new interface driver uas
[    1.022504] usbcore: registered new interface driver usb-storage
[    1.022605] usbcore: registered new interface driver usbserial_generic
[    1.022683] usbserial: USB Serial support registered for generic
[    1.022745] usbcore: registered new interface driver ch341
[    1.022785] usbserial: USB Serial support registered for ch341-uart
[    1.022851] usbcore: registered new interface driver cp210x
[    1.022925] usbserial: USB Serial support registered for cp210x
[    1.023008] usbcore: registered new interface driver ftdi_sio
[    1.023049] usbserial: USB Serial support registered for FTDI USB Serial Device
[    1.023226] usbcore: registered new interface driver option
[    1.023266] usbserial: USB Serial support registered for GSM modem (1-port)
[    1.023487] usbcore: registered new interface driver pl2303
[    1.023527] usbserial: USB Serial support registered for pl2303
[    1.023635] usbcore: registered new interface driver qcserial
[    1.023673] usbserial: USB Serial support registered for Qualcomm USB modem
[    1.024033] mousedev: PS/2 mouse device common for all mice
[    1.024829] <<-GTP-INFO->> GTP driver installing
[    1.026208] i2c /dev entries driver
[    1.029489] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
[    1.030748] vdd_cpu_b: supplied by vcc3v3_sys
[    1.031796] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected!
[    1.032921] vdd_gpu: supplied by vcc3v3_sys
[    1.033643] rk808 0-001b: chip id: 0x0
[    1.037361] rk808-regulator rk808-regulator: there is no dvs0 gpio
[    1.037398] rk808-regulator rk808-regulator: there is no dvs1 gpio
[    1.038241] vdd_center: supplied by vcc3v3_sys
[    1.038914] vdd_cpu_l: supplied by vcc3v3_sys
[    1.039213] vcc_ddr: supplied by vcc3v3_sys
[    1.039785] vcc_1v8: supplied by vcc3v3_sys
[    1.040590] vcc1v8_dvp: supplied by vcc3v3_sys
[    1.041127] vcc3v0_tp: supplied by vcc3v3_sys
[    1.041823] vcc1v8_pmu: supplied by vcc3v3_sys
[    1.042546] vccio_sd: supplied by vcc3v3_sys
[    1.043093] vcca3v0_codec: supplied by vcc3v3_sys
[    1.043790] vcc_1v5: supplied by vcc3v3_sys
[    1.044347] vcca1v8_codec: supplied by vcc3v3_sys
[    1.045038] vcc_3v0: supplied by vcc3v3_sys
[    1.045449] vcc3v3_s3: supplied by vcc3v3_sys
[    1.045927] vcc3v3_s0: supplied by vcc3v3_sys
[    1.049120] rk808-rtc rk808-rtc: registered as rtc0
[    1.049661] rk808-rtc rk808-rtc: setting system clock to 2023-03-21 12:48:37 UTC (1679402917)
[    1.050803] fusb302 4-0022: Can't get property of role, set role to default DRP
[    1.053851] fusb302 4-0022: port 0 probe success with role ROLE_MODE_DRP, try_role ROLE_MODE_NONE
[    1.053984] input: Typec_Headphone as /devices/platform/ff3d0000.i2c/i2c-4/4-0022/input/input0
[    1.055052] dw9718 1-000c: probing...
[    1.055075] dw9718 1-000c: could not get module rockchip,vcm-start-current from dts!
[    1.055089] dw9718 1-000c: could not get module rockchip,vcm-rated-current from dts!
[    1.055105] dw9718 1-000c: could not get module rockchip,vcm-step-mode from dts!
[    1.055116] dw9718 1-000c: could not get module rockchip,vcm-control-mode from dts!
[    1.055131] dw9718 1-000c: could not get module rockchip,vcm-sacdiv-mode from dts!
[    1.055165] dw9718 1-000c: probing successful
[    1.055243] dw9718 2-000c: probing...
[    1.055260] dw9718 2-000c: could not get module rockchip,vcm-start-current from dts!
[    1.055272] dw9718 2-000c: could not get module rockchip,vcm-rated-current from dts!
[    1.055286] dw9718 2-000c: could not get module rockchip,vcm-step-mode from dts!
[    1.055297] dw9718 2-000c: could not get module rockchip,vcm-control-mode from dts!
[    1.055311] dw9718 2-000c: could not get module rockchip,vcm-sacdiv-mode from dts!
[    1.055336] dw9718 2-000c: probing successful
[    1.055474] IR NEC protocol handler initialized
[    1.056188] iommu: Adding device ff910000.rkisp1 to group 5
[    1.056224] rkisp1 ff910000.rkisp1: Linked as a consumer to ff914000.iommu
[    1.056502] rkisp1 ff910000.rkisp1: rkisp1 driver version: v00.01.05
[    1.056537] rkisp1 ff910000.rkisp1: Missing rockchip,grf property
[    1.056830] rkisp1 ff910000.rkisp1: Entity type for entity rkisp1-isp-subdev was not initialized!
[    1.057745] iommu: Adding device ff920000.rkisp1 to group 6
[    1.057776] rkisp1 ff920000.rkisp1: Linked as a consumer to ff924000.iommu
[    1.057997] rkisp1 ff920000.rkisp1: rkisp1 driver version: v00.01.05
[    1.058033] rkisp1 ff920000.rkisp1: Missing rockchip,grf property
[    1.058264] rkisp1 ff920000.rkisp1: Entity type for entity rkisp1-isp-subdev was not initialized!
[    1.060377] rockchip-iodomain ff320000.syscon:io-domains: Linked as a consumer to regulator.21
[    1.060422] rockchip-iodomain ff320000.syscon:io-domains: pmu1830(3000000 uV) supplied by vcc_3v0
[    1.060667] rockchip-iodomain ff770000.syscon:io-domains: Linked as a consumer to regulator.14
[    1.060702] rockchip-iodomain ff770000.syscon:io-domains: bt656(1800000 uV) supplied by vcc1v8_dvp
[    1.060791] rockchip-iodomain ff770000.syscon:io-domains: Linked as a consumer to regulator.20
[    1.060823] rockchip-iodomain ff770000.syscon:io-domains: audio(1800000 uV) supplied by vcca1v8_codec
[    1.060916] rockchip-iodomain ff770000.syscon:io-domains: Linked as a consumer to regulator.17
[    1.060950] rockchip-iodomain ff770000.syscon:io-domains: sdmmc(3000000 uV) supplied by vccio_sd
[    1.061031] rockchip-iodomain ff770000.syscon:io-domains: Linked as a consumer to regulator.21
[    1.061063] rockchip-iodomain ff770000.syscon:io-domains: gpio1830(3000000 uV) supplied by vcc_3v0
[    1.062345] __power_supply_register: Expected proper parent device for 'test_ac'
[    1.062512] __power_supply_register: Expected proper parent device for 'test_battery'
[    1.062741] thermal thermal_zone2: power_allocator: sustainable_power will be estimated
[    1.062827] __power_supply_register: Expected proper parent device for 'test_usb'
[    1.064764] rockchip-thermal ff260000.tsadc: tsadc is probed successfully!
[    1.066043] device-mapper: uevent: version 1.0.3
[    1.066318] device-mapper: ioctl: 4.39.0-ioctl (2018-04-03) initialised: dm-devel@redhat.com
[    1.066470] device-mapper: verity-avb: AVB error handler initialized with vbmeta device: 
[    1.066756] cpu cpu0: bin=1
[    1.066791] cpu cpu0: leakage=17
[    1.066915] cpu cpu0: Linked as a consumer to regulator.11
[    1.078789] cpu cpu0: temp=48750, pvtm=148270 (147808 + 462)
[    1.079055] cpu cpu0: Dropping the link to regulator.11
[    1.079104] cpu cpu0: pvtm-volt-sel=1
[    1.079128] cpu cpu0: bin-scale=34
[    1.079206] cpu cpu4: bin=1
[    1.079240] cpu cpu4: leakage=31
[    1.079326] cpu cpu4: Linked as a consumer to regulator.8
[    1.091293] cpu cpu4: temp=48125, pvtm=153124 (152879 + 245)
[    1.091430] cpu cpu4: Dropping the link to regulator.8
[    1.091474] cpu cpu4: pvtm-volt-sel=1
[    1.091499] cpu cpu4: bin-scale=17
[    1.091783] cpu cpu0: Linked as a consumer to regulator.11
[    1.091846] cpu cpu0: Dropping the link to regulator.11
[    1.091986] cpu cpu0: Linked as a consumer to regulator.11
[    1.092684] cpu cpu0: avs=0
[    1.092944] cpu cpu0: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[    1.093572] cpu cpu0: failed to find power_model node
[    1.093729] cpu cpu4: Linked as a consumer to regulator.8
[    1.094529] cpu cpu4: avs=0
[    1.094574] energy_model: pd4: hertz/watts ratio non-monotonically decreasing: em_cap_state 2 >= em_cap_state1
[    1.094844] cpu cpu4: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[    1.096778] cpu cpu4: failed to find power_model node
[    1.098295] sdhci: Secure Digital Host Controller Interface driver
[    1.098321] sdhci: Copyright(c) Pierre Ossman
[    1.098339] Synopsys Designware Multimedia Card Interface Driver
[    1.099222] dwmmc_rockchip fe310000.mmc: IDMAC supports 32-bit address mode.
[    1.099633] dwmmc_rockchip fe310000.mmc: Using internal DMA controller.
[    1.099696] dwmmc_rockchip fe310000.mmc: Version ID is 270a
[    1.099796] dwmmc_rockchip fe310000.mmc: DW MMC controller at irq 28,32 bit host data width,256 deep fifo
[    1.099980] dwmmc_rockchip fe310000.mmc: allocated mmc-pwrseq
[    1.100006] mmc_host mmc0: card is non-removable.
[    1.112513] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    1.126150] dwmmc_rockchip fe320000.mmc: IDMAC supports 32-bit address mode.
[    1.126512] dwmmc_rockchip fe320000.mmc: Using internal DMA controller.
[    1.126550] dwmmc_rockchip fe320000.mmc: Version ID is 270a
[    1.126632] dwmmc_rockchip fe320000.mmc: DW MMC controller at irq 29,32 bit host data width,256 deep fifo
[    1.126764] dwmmc_rockchip fe320000.mmc: Linked as a consumer to regulator.4
[    1.126862] dwmmc_rockchip fe320000.mmc: Linked as a consumer to regulator.17
[    1.139082] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    1.147749] mmc0: queuing unknown CIS tuple 0x80 (2 bytes)
[    1.150084] mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
[    1.150995] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.152168] mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
[    1.156035] mmc0: queuing unknown CIS tuple 0x80 (7 bytes)
[    1.161166] mmc0: queuing unknown CIS tuple 0x81 (9 bytes)
[    1.175698] mmc2: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA
[    1.180038] ledtrig-cpu: registered to indicate activity on CPUs
[    1.180554] hidraw: raw HID events driver (C) Jiri Kosina
[    1.181100] usbcore: registered new interface driver usbhid
[    1.181126] usbhid: USB HID core driver
[    1.181140] ion_device_add_heap: ion_system_contig_heap id=0 type=1
[    1.181409] ion_device_add_heap: ion_system_heap id=1 type=0
[    1.181443] ion_device_add_heap: reserved id=2 type=4
[    1.181743] ashmem: initialized
[    1.185841] rockchip-saradc ff100000.saradc: ff100000.saradc supply vref not found, using dummy regulator
[    1.185972] rockchip-saradc ff100000.saradc: Linked as a consumer to regulator.0
[    1.187164] optee: probing for conduit method from DT.
[    1.187222] optee: revision 1.0
[    1.187227] optee: api revision mismatch
[    1.190328] rt5651 1-001a: Device with ID register 0xffffffc0 is not rt5651
[    1.195523] Initializing XFRM netlink socket
[    1.195624] IPsec XFRM device driver
[    1.196706] NET: Registered protocol family 10
[    1.199145] Segment Routing with IPv6
[    1.199352] mmc_host mmc1: Bus speed (slot 0) = 150000000Hz (slot req 150000000Hz, actual 150000000HZ div = 0)
[    1.205242] mmc2: new HS200 MMC card at address 0001
[    1.206877] bpfilter: Loaded bpfilter_umh pid 101
Started bpfilter
[    1.207042] mmcblk2: mmc2:0001 AJTD4R 14.6 GiB 
[    1.207470] NET: Registered protocol family 17
[    1.207603] mmcblk2boot0: mmc2:0001 AJTD4R partition 1 4.00 MiB
[    1.207709] Bluetooth: RFCOMM TTY layer initialized
[    1.207725] Bluetooth: RFCOMM socket layer initialized
[    1.207747] Bluetooth: RFCOMM ver 1.11
[    1.207769] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    1.207787] Bluetooth: HIDP socket layer initialized
[    1.207827] [BT_RFKILL]: Enter rfkill_rk_init
[    1.207837] [WLAN_RFKILL]: Enter rfkill_wlan_init
[    1.208110] mmcblk2boot1: mmc2:0001 AJTD4R partition 2 4.00 MiB
[    1.208258] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[    1.208297] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6212
[    1.208308] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[    1.208316] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[    1.208335] mmcblk2rpmb: mmc2:0001 AJTD4R partition 3 4.00 MiB, chardev (239:0)
[    1.208352] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,host_wake_irq = 3, flags = 0.
[    1.208364] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[    1.208371] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[    1.208379] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 1
[    1.208386] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[    1.208762] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 83.
[    1.208790] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 9.
[    1.208808] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 90.
[    1.208829] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 4.
[    1.208888] [BT_RFKILL]: Request irq for bt wakeup host
[    1.208994] [BT_RFKILL]: ** disable irq
[    1.209079] [BT_RFKILL]: bt shut off power
[    1.211094]  mmcblk2: p1 p2 p3 p4 p5 p6 p7 p8 p9
[    1.235635] [BT_RFKILL]: bt_default device registered.
[    1.235727] Key type dns_resolver registered
[    1.236441] ov4689 1-0036: driver version: 00.01.08
[    1.236607] ov4689 1-0036: 1-0036 supply avdd not found, using dummy regulator
[    1.236664] ov4689 1-0036: Linked as a consumer to regulator.0
[    1.236698] ov4689 1-0036: 1-0036 supply dovdd not found, using dummy regulator
[    1.236748] ov4689 1-0036: 1-0036 supply dvdd not found, using dummy regulator
[    1.238244] vendor storage:20190527 ret = 0
[    1.238742] ov4689 1-0036: Unexpected sensor id(000000), ret(-5)
[    1.239056] ov4689 2-0036: driver version: 00.01.08
[    1.239189] ov4689 2-0036: 2-0036 supply avdd not found, using dummy regulator
[    1.239234] ov4689 2-0036: Linked as a consumer to regulator.0
[    1.239258] ov4689 2-0036: 2-0036 supply dovdd not found, using dummy regulator
[    1.239316] ov4689 2-0036: 2-0036 supply dvdd not found, using dummy regulator
[    1.240608] ov4689 2-0036: Unexpected sensor id(000000), ret(-5)
[    1.240917] ov13850 1-0010: driver version: 00.01.05
[    1.240945] ov13850 1-0010: Failed to get power-gpios, maybe no use
[    1.241001] ov13850 1-0010: 1-0010 supply avdd not found, using dummy regulator
[    1.241038] ov13850 1-0010: Linked as a consumer to regulator.0
[    1.241061] ov13850 1-0010: 1-0010 supply dovdd not found, using dummy regulator
[    1.241107] ov13850 1-0010: 1-0010 supply dvdd not found, using dummy regulator
[    1.243780] ov13850 1-0010: Unexpected sensor id(000000), ret(-5)
[    1.244018] ov13850 2-0010: driver version: 00.01.05
[    1.244044] ov13850 2-0010: Failed to get power-gpios, maybe no use
[    1.244100] ov13850 2-0010: 2-0010 supply avdd not found, using dummy regulator
[    1.244137] ov13850 2-0010: Linked as a consumer to regulator.0
[    1.244160] ov13850 2-0010: 2-0010 supply dovdd not found, using dummy regulator
[    1.244206] ov13850 2-0010: 2-0010 supply dvdd not found, using dummy regulator
[    1.247140] ov13850 2-0010: Unexpected sensor id(000000), ret(-5)
[    1.247906] registered taskstats version 1
[    1.247915] Loading compiled-in X.509 certificates
[    1.248014] Key type ._fscrypt registered
[    1.248021] Key type .fscrypt registered
[    1.248027] Key type fscrypt-provisioning registered
[    1.248288] pstore: Using compression: deflate
[    1.249041] rga2: Driver loaded successfully ver:3.2.18218
[    1.249240] rga2: Module initialized.
[    1.265744] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[    1.274387] mmc0: new high speed SDIO card at address 0001
[    1.280568] phy phy-ff770000.syscon:usb2-phy@e450.9: Linked as a consumer to regulator.2
[    1.281412] phy phy-ff770000.syscon:usb2-phy@e450.10: No vbus specified for otg port
[    1.283575] rockchip-drm display-subsystem: dmc is disabled
[    1.283728] rockchip-vop ff8f0000.vop: missing rockchip,grf property
[    1.283836] rockchip-drm display-subsystem: bound ff8f0000.vop (ops 0xffffff8008f806a8)
[    1.283881] rockchip-vop ff900000.vop: missing rockchip,grf property
[    1.284044] rockchip-drm display-subsystem: bound ff900000.vop (ops 0xffffff8008f806a8)
[    1.284082] rockchip-dp ff970000.edp: no DP phy configured
[    1.284815] rockchip-drm display-subsystem: bound ff970000.edp (ops 0xffffff8008f8acd0)
[    1.285153] rockchip-drm display-subsystem: bound fec00000.dp (ops 0xffffff8008f8b4d8)
[    1.285330] dwhdmi-rockchip ff940000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[    1.285578] cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] Not connected. Disabling cdn
[    1.287588] rockchip-drm display-subsystem: bound ff940000.hdmi (ops 0xffffff8008f8b6d8)
[    1.287612] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    1.287619] [drm] No driver support for vblank timestamp query.
[    1.313820] rockchip-drm display-subsystem: connector[eDP-1] can't found any modes
[    1.313841] rockchip-drm display-subsystem: can't not find any loader display
[    1.313854] rockchip-drm display-subsystem: failed to show loader logo
[    1.390224] rockchip-vop ff900000.vop: [drm:vop_crtc_atomic_enable] Update mode to 1920x1080p60, type: 11
[    1.460043] Console: switching to colour frame buffer device 240x67
[    1.477408] rockchip-drm display-subsystem: fb0:  frame buffer device
[    1.478319] [drm] Initialized rockchip 2.0.0 20140818 for display-subsystem on minor 0
[    1.478857] midgard ff9a0000.gpu: Linked as a consumer to regulator.9
[    1.478989] midgard ff9a0000.gpu: leakage=24
[    1.491711] midgard ff9a0000.gpu: temp=46250, pvtm=124277 (124217 + 60)
[    1.493614] midgard ff9a0000.gpu: pvtm-volt-sel=1
[    1.494104] midgard ff9a0000.gpu: avs=0
[    1.494727] midgard ff9a0000.gpu: GPU identified as 0x0860 r2p0 status 0
[    1.494855] midgard ff9a0000.gpu: Protected mode not available
[    1.495456] midgard ff9a0000.gpu: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[    1.495513] midgard ff9a0000.gpu: Using configured power model mali-simple-power-model, and fallback mali-simple-power-model
[    1.495629] I : [File] : drivers/gpu/arm/midgard/backend/gpu/mali_kbase_devfreq.c; [Line] : 417; [Func] : midgard_kbase_devfreq_init(); success initing power_model_simple.
[    1.496058] midgard ff9a0000.gpu: Probed as mali0
[    1.496429] dwc3 fe800000.dwc3: Failed to get clk 'ref': -2
[    1.504043] ehci-platform fe380000.usb: EHCI Host Controller
[    1.504078] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 5
[    1.504436] ehci-platform fe380000.usb: irq 31, io mem 0xfe380000
[    1.515823] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
[    1.516096] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[    1.516111] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.516120] usb usb5: Product: EHCI Host Controller
[    1.516127] usb usb5: Manufacturer: Linux 4.19.193 ehci_hcd
[    1.516134] usb usb5: SerialNumber: fe380000.usb
[    1.516529] hub 5-0:1.0: USB hub found
[    1.516585] hub 5-0:1.0: 1 port detected
[    1.517442] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
[    1.517504] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 6
[    1.517792] ohci-platform fe3a0000.usb: irq 32, io mem 0xfe3a0000
[    1.522803] dwmmc_rockchip fe320000.mmc: Successfully tuned phase to 212
[    1.522831] mmc1: new ultra high speed SDR104 SDXC card at address 59b4
[    1.524079] mmcblk1: mmc1:59b4 USD00 120 GiB 
[    1.542908]  mmcblk1: p1 p2 p3
[    1.576623] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[    1.576652] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.576661] usb usb6: Product: Generic Platform OHCI controller
[    1.576669] usb usb6: Manufacturer: Linux 4.19.193 ohci_hcd
[    1.576677] usb usb6: SerialNumber: fe3a0000.usb
[    1.577023] hub 6-0:1.0: USB hub found
[    1.577057] hub 6-0:1.0: 1 port detected
[    1.577588] input: adc-keys as /devices/platform/adc-keys/input/input1
[    1.578903] asoc-simple-card hdmi-sound: i2s-hifi <-> ff8a0000.i2s mapping ok
[    1.580917] input: gpio-keys as /devices/platform/gpio-keys/input/input2
[    1.583337] rkisp1 ff910000.rkisp1: clear unready subdev num: 3
[    1.583850] rockchip-mipi-dphy-rx: No link between dphy and sensor
[    1.583866] rkisp1: update sensor failed
[    1.583878] rkisp1 ff920000.rkisp1: clear unready subdev num: 2
[    1.584243] rockchip-mipi-dphy-rx: No link between dphy and sensor
[    1.584261] rkisp1: update sensor failed
[    1.584351] ALSA device list:
[    1.584363]   #0: rockchip,hdmi
[    2.162696] phy phy-ff770000.syscon:usb2-phy@e450.10: charger = USB_DCP_CHARGER
[    2.177359] Freeing unused kernel memory: 10752K
[    2.177590] Run /init as init process
Loading, please wait...
Starting version 245.4-4ubuntu3.2
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[    2.770436] EXT4-fs (mmcblk2p8): mounted filesystem with ordered data mode. Opts: (null)
Begin: Will now check userdata file system ... fsck from util-linux 2.34
[/usr/sbin/fsck.ext4 (1) -- /dev/mmcblk2p9] fsck.ext4 -a -C0 /dev/mmcblk2p9 
userdata: clean, 58/716800 files, 46243/3637755 blocks
done.
[    2.839159] EXT4-fs (mmcblk2p9): mounted filesystem with ordered data mode. Opts: (null)
[    2.844108] EXT4-fs (mmcblk2p9): re-mounted. Opts: (null)
[    2.850735] overlayfs: "xino" feature enabled using 32 upper inode bits.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
mount: /proc: proc already mounted on /proc.
Starting syslogd: OK
Starting klogd: OK
Loading modules: r8169[    3.113396] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    3.134979] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    3.135849] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    3.135864] platform regulatory.0: Falling back to syfs fallback for: regulatory.db
[    3.250969] [dhd] dhd_module_init: in Dongle Host Driver, version 100.10.545.19 (r826445-20210310-3)
[    3.250996] [dhd] ======== dhd_wlan_init_plat_data ========
[    3.251002] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter
[    3.251039] [dhd] dhd_wlan_init_gpio: WL_HOST_WAKE=-1, oob_irq=93, oob_irq_flags=0x414
[    3.251045] [dhd] dhd_wlan_init_gpio: WL_REG_ON=-1
[    3.251050] [dhd] dhd_wifi_platform_load: Enter
[    3.251055] [dhd] Power-up adapter 'DHD generic adapter'
[    3.251902] [dhd] wifi_platform_set_power = 1, delay: 200 msec
[    3.251913] [dhd] ======== PULL WL_REG_ON(-1) HIGH! ========
[    3.251918] [WLAN_RFKILL]: rockchip_wifi_power: 1
[    3.251924] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
[    3.251929] [WLAN_RFKILL]: wifi turn on power [GPIO-1-0]
[    3.555930] [dhd] wifi_platform_bus_enumerate device present 1
[    3.555993] [dhd] ======== Card detection to detect SDIO card! ========
[    3.556016] mmc0:mmc host rescan start!
[    3.572227] [dhd] bcmsdh_register: register client driver
[    3.572845] [dhd] bcmsdh_sdmmc_probe: Enter num=1
[    3.573118] [dhd] bcmsdh_sdmmc_probe: Enter num=2
[    3.573125] [dhd] bus num (host idx)=0, slot num (rca)=1
[    3.573132] [dhd] found adapter info 'DHD generic adapter'
[    3.573298] [dhd] sdioh_attach: set sd_f2_blocksize 256
[    3.573417] [dhd] sdioh_attach: sd clock rate = 0
[    3.573951] [dhd] dhdsdio_probe : no mutex held. set lock
[    3.574123] [dhd] F1 signature read @0x18000000=0x1541a9a6
[    3.579144] [dhd] F1 signature OK, socitype:0x1 chip:0xa9a6 rev:0x1 pkg:0x4
[    3.580344] [dhd] DHD: dongle ram size is set to 524288(orig 524288) at 0x0
[    3.580519] [dhd] dhd_conf_set_chiprev : devid=0xa9a6, chip=0xa9a6, chiprev=1
[    3.581555] [dhd] dhd_log_dump_init: kernel log buf size = 256KB; logdump_prsrv_tailsize = 80KB; limit prsrv tail size to = 38KB
[    3.582636] [dhd] dhd_attach(): thread:dhd_watchdog_thread:e6 started
[    3.582759] [dhd] dhd_attach(): thread:dhd_dpc:e7 started
[    3.582955] [dhd] dhd_attach(): thread:dhd_rxf:e8 started
[    3.582976] [dhd] dhd_deferred_work_init: work queue initialized
[    3.582993] [dhd] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 2
[    3.583912] [dhd] get_mem_val_from_file: File [/data/misc/wifi/.memdump.info] doesn't exist
[    3.583927] [dhd] dhd_get_memdump_info: MEMDUMP ENABLED = 3
[    3.583936] [dhd] sdioh_cis_read: func_cis_ptr[0]=0x1070
[    3.594501] [dhd] dhdsdio_probe_init: making DHD_BUS_DOWN
[    3.594668] [dhd] Dongle Host Driver, version 100.10.545.19 (r826445-20210310-3)
[    3.595005] [dhd] Register interface [wlan0]  MAC: 8c:f7:10:fe:64:fe
[    3.59500 bcmdhd                                                    [  OK  1;34m]
 
[    3.595060] [dhd] dhd_dbg_detach_pkt_monitor, 2099
[    3.595074] [dhd] dhdRunning sysctl: _bus_devreset: == Power OFF ==
[    3.595294] [dhd] dhd_bus_stop: making DHD_BUS_DOWN
[    3.595329] [dhd] bcmsdh_oob_intr_unregister: Enter
[    3.595337] [dhd] bcmsdh_oob_intr_unregister: irq is not registered
[    3.595347] [dhd] dhd_bus_devreset: making dhdpub up FALSE
[    3.595356] [dhd] dhd_txglom_enable: enable 0
[    3.595363] [dhd] dhd_bus_devreset: making DHD_BUS_DOWN
[    3.595371] [dhd] dhd_bus_devreset:  WLAN OFF DONE
[    3.595419] [dhd] wifi_platform_set_power = 0, delay: 0 msec
[    3.595429] [dhd] ======== PULL WL_REG_ON(-1) LOW! ========
[    3.595437] [WLAN_RFKILL]: rockchip_wifi_power: 0
[    3.595451] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
[    3.595458] [WLAN_RFKILL]: wifi shut off power [GPIO-1-1]
[    3.595466] [dhd] dhdsdio_probe : the lock is released.
[    3.595517] [dhd] dhd_module_init: Exit err=0
OK
/usr/bin/modetest
Populating /dev using udev: [    4.211492] udevd[263]: starting version 3.2.7
[    4.220470] udevd[263]: specified group 'kvm' unknown
[    4.232003] udevd[264]: starting eudev-3.2.7
[    4.253575] udevd[264]: specified group 'kvm' unknown
[    4.395448] usbcore: registered new interface driver brcmfmac
[    4.632623] FAT-fs (mmcblk1p1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
done
Initializing random number generator... done.
Will now mount all partitions in /etc/fstab
Note: Create /.skip_fsck to skip fsck
 - The check might take a while if didn't shutdown properly!
Handling misc: /dev/mmcblk2p3 /misc emmc defaults 0
Unsupported file system emmc for /dev/mmcblk2p3
Log saved to /tmp/mountall.log
Starting system message bus: nohup: appending output to 'nohup.out'
done
Starting network: [    5.066886] RTL8211E Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211E Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[    5.070211] rk_gmac-dwmac fe300000.ethernet eth0: No Safety Features support found
[    5.070288] rk_gmac-dwmac fe300000.ethernet eth0: PTP not supported by HW
[    5.070556] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
udhcpc: started, v1.34.1
udhcpc: broadcasting discover
udhcpc: broadcasting discover
[   11.146973] rk_gmac-dwmac fe300000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   11.147106] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
udhcpc: broadcasting discover
udhcpc: no lease, forking to background
ip: can't find device 'eth1'
ip: SIOCGIFFLAGS: No such device
ip: can't find device 'eth2'
ip: SIOCGIFFLAGS: No such device
FAIL
Starting dhcpcd...
dev: loaded udev
[   14.428174] [dhd] dhd_ioctl_entry: Interface is down 
[   14.428208] [dhd] WEXT-ERROR) wl_iw_get_essid : Error getting the SSID -22
DUID 00:01:00:01:2b:ab:26:cd:2a:2d:2a:8a:d6:44
eth0: IAID 2a:8a:d6:44
[   14.479128] [dhd] dhd_open: Enter wlan0
[   14.479164] [dhd] dhd_open : no mutex held. set lock
[   14.479174] [dhd] 
[   14.479174] Dongle Host Driver, version 100.10.545.19 (r826445-20210310-3)
[   14.479190] [dhd][wlan0] wl_android_wifi_on : in g_wifi_on=0
[   14.479197] [dhd] wifi_platform_set_power = 1, delay: 200 msec
[   14.479207] [dhd] ======== PULL WL_REG_ON(-1) HIGH! ========
[   14.479213] [WLAN_RFKILL]: rockchip_wifi_power: 1
[   14.479220] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
[   14.479226] [WLAN_RFKILL]: wifi turn on power [GPIO-1-0]
[   14.786033] sdio_reset_comm():
[   14.812829] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[   14.829971] mmc_host mmc0: Bus speed (slot 0) = 100000Hz (slot req 100000Hz, actual 100000HZ div = 0)
[   14.888761] mmc0: queuing unknown CIS tuple 0x80 (2 bytes)
[   14.895892] mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
[   14.902890] mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
[   14.915765] mmc0: queuing unknown CIS tuple 0x80 (7 bytes)
[   14.931390] mmc0: queuing unknown CIS tuple 0x81 (9 bytes)
[   15.311604] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[   15.311879] [dhd] sdioh_start: set sd_f2_blocksize 256
[   15.313152] [dhd] dhd_bus_devreset: == Power ON ==
[   15.313409] [dhd] F1 signature read @0x18000000=0x1541a9a6
[   15.319124] [dhd] F1 signature OK, socitype:0x1 chip:0xa9a6 rev:0x1 pkg:0x4
[   15.321071] [dhd] DHD: dongle ram size is set to 524288(orig 524288) at 0x0
[   15.321378] [dhd] dhd_bus_devreset: making DHD_BUS_DOWN
[   15.321513] [dhd] dhdsdio_probe_init: making DHD_BUS_DOWN
[   15.324356] [dhd] dhd_conf_read_config : Ignore config file /system/etc/firmware/config.txt
[   15.324532] [dhd] dhd_conf_set_path_params : Final fw_path=/system/etc/firmware/fw_bcm43438a1.bin
[   15.324627] [dhd] dhd_conf_set_path_params : Final nv_path=/system/etc/firmware/nvram_ap6212a.txt
[   15.324767] [dhd] dhd_conf_set_path_params : Final clm_path=/system/etc/firmware/clm_bcm43438a1.blob
[   15.324859] [dhd] dhd_conf_set_path_params : Final conf_path=/system/etc/firmware/config.txt
[   15.331644] [dhd] dhd_os_open_image1: /system/etc/firmware/fw_bcm43438a1.bin (414579 bytes) open success
[   15.475332] [dhd] dhd_os_open_image1: /system/etc/firmware/nvram_ap6212a.txt (1003 bytes) open success
[   15.476747] [dhd] NVRAM version: AP6212A_NVRAM_V1.0.1_20160606
[   15.478090] [dhd] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
[   15.555457] [dhd] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
[   15.556102] [dhd] bcmsdh_oob_intr_register: HW_OOB irq=93 flags=0x4
[   15.556393] [dhd] get_mem_val_from_file: File [/data/misc/wifi/.memdump.info] doesn't exist
[   15.556439] [dhd] dhd_get_memdump_info: MEMDUMP ENABLED = 3
[   15.559278] [dhd] dhd_tcpack_suppress_set: TCP ACK Suppress mode 2 -> mode 0
[   15.563328] [dhd] dhd_apply_default_clm: Ignore clm file /system/etc/firmware/clm_bcm43438a1.blob
[   15.568499] [dhd] Firmware up: op_mode=0x0005, MAC=8c:f7:10:fe:64:fe
[   15.569569] [dhd] Disable tdls_auto_op failed. -1
[   15.575326] [dhd] dhd_preinit_ioctls Set scancache failed -23
[   15.576805] [dhd] dhd_preinit_ioctls: event_log_max_sets: 26 ret: -23
[   15.598298] [dhd]   Driver: 100.10.545.19 (r826445-20210310-3)
[   15.598298]   Firmware: wl0: Jun 13 2018 13:18:38 version 7.45.96.24 (7ffe8b7@shgit) (r) FWID 01-40f9deb0 es7.c5.n4.a3
[   15.598298]   CLM: 7.11.15 (2014-05-26 10:53:55) 
[   15.599556] [dhd] dhd_preinit_ioctls wlc_ver failed -23
[   15.600408] [dhd] dhd_txglom_enable: enable 1
[   15.600449] [dhd] dhd_conf_set_txglom_params : txglom_mode=multi-desc
[   15.600488] [dhd] dhd_conf_set_txglom_params : txglomsize=36, deferred_tx_len=0
[   15.600553] [dhd] dhd_conf_set_txglom_params : txinrx_thres=-1, dhd_txminmax=1
[   15.600591] [dhd] dhd_conf_set_txglom_params : tx_max_offset=0, txctl_tmo_fix=300
[   15.600632] [dhd] dhd_conf_get_disable_proptx : fw_proptx=1, disable_proptx=-1
[   15.603132] [dhd] dhd_wlfc_hostreorder_init(): successful bdcv2 tlv signaling, 64
[   15.607213] [dhd] dhd_pno_init: Support Android Location Service
[   15.635547] [dhd] rtt_do_get_ioctl: failed to send getbuf proxd iovar (CMD ID : 1), status=-23
[   15.635818] [dhd] dhd_rtt_init : FTM is not supported
[   15.637497] [dhd] dhd_rtt_ftm_config : failed to set config
[   15.640724] [dhd] dhd_wl_ioctl_get_intiovar: get int iovar wnm_bsstrans_resp failed, ERR -23
[   15.640881] [dhd] failed to get wnm_bsstrans_resp
[   15.641860] [dhd] failed to set WNM capabilities
[   15.679093] [dhd] dhd_preinit_ioctls: Failed to get preserve log # !
[   15.679930] [dhd] dhd_conf_set_country : set country CN, revision 0
[   15.684132] [dhd] dhd_conf_set_country : Country code: CN (CN/0)
[   15.693137] [dhd] CONFIG-ERROR) dhd_conf_set_intiovar : ampdu_mpdu setting failed -29
[   15.693317] [dhd][wlan0] wl_android_wifi_on : Success
[   15.729042] [dhd] CFG80211-ERROR) __wl_update_wiphybands : error reading vhtmode (-23)
[   15.765757] [dhd] dhd_open : the lock is released.
[   15.765922] [dhd] dhd_open: Exit wlan0 ret=0
[   15.766015] [dhd] [wlan0] tx queue started
wlan0: waiting for carrier
eth0: rebinding lease of 192.168.1.122
eth0: soliciting an IPv6 router
wlan0: carrier acquired
wlan0: IAID 10:fe:64:fe
wlan0: adding address fe80::6fb2:dee2:73ff:7e25
eth0: Router Advertisement from fe80::769d:79ff:fe51:beb8
eth0: adding address fd84:f463:5c16:0:30c7:3864:4252:d2f3/64
eth0: adding route to fd84:f463:5c16::/64
eth0: soliciting a DHCPv6 lease
eth0: probing address 192.168.1.122/24
wlan0: soliciting an IPv6 router
eth0: REPLY6 received from fe80::769d:79ff:fe51:beb8
eth0: adding address fd84:f463:5c16::459/128
eth0: renew in 21600, rebind in 34560, expire in 43200 seconds
wlan0: soliciting a DHCP lease
forked to background, child pid 575
Starting ntpd: OK
Starting dropbear sshd: OK
Starting launcher: Starting dnsmasq: OK
Starting input-event-daemon: input-event-daemon: Start parsing /etc/input-event-daemon.conf...
input-event-daemon: Adding device: /dev/input/event0...
input-event-daemon: Adding device: /dev/input/event1...
input-event-daemon: Adding device: /dev/input/event2...
input-event-daemon: Start listening on 3 devices...
done
[root@rk3399:/]# Date: 2023-03-21 UTC
[12:48:53.717] weston 10.0.0
               https://wayland.freedesktop.org
               Bug reports to: https://gitlab.freedesktop.org/wayland/weston/issues/
               Build: 10.0.0
[12:48:53.719] Command line: weston --tty=2 --idle-time=0
[12:48:53.719] OS: Linux, 4.19.193, #1 SMP PREEMPT Fri Aug 19 16:48:03 CST 2022, aarch64
[12:48:53.720] Flight recorder: enabled
[12:48:53.720] warning: XDG_RUNTIME_DIR "/var/run" is not configured
correctly.  Unix access mode must be 0700 (current mode is 0755),
and must be owned by the user UID 0 (current owner is UID 0).
Refer to your distribution on how to get it, or
http://www.freedesktop.org/wiki/Specifications/basedir-spec
on how to implement it.
[12:48:53.724] Using config file '/etc/xdg/weston/weston.ini'
[12:48:53.725] Output repaint window is -1 ms maximum.
[12:48:53.725] Loading module '/usr/lib/libweston-10/drm-backend.so'
[12:48:53.728] initializing drm backend
[12:48:53.728] Entering mirror mode.
[12:48:53.728] Trying weston_launch launcher...
[12:48:53.728] could not get launcher fd from env
[12:48:53.728] Trying direct launcher...
[12:48:53.731] using /dev/dri/card0
[12:48:53.731] DRM: does not support atomic modesetting
[12:48:53.731] DRM: does not support GBM modifiers
[12:48:53.731] DRM: supports picture aspect ratio
[12:48:53.733] Loading module '/usr/lib/libweston-10/gl-renderer.so'
[12:48:53.738] EGL client extensions: EGL_EXT_client_extensions
               EGL_EXT_platform_base EGL_KHR_client_get_all_proc_addresses
               EGL_KHR_platform_gbm EGL_MESA_platform_gbm
               EGL_KHR_platform_wayland EGL_EXT_platform_wayland
arm_release_ver of this libmali is 'r18p0-01rel0', rk_so_ver is '5'.
[12:48:53.747] EGL version: 1.4 Midgard-"r18p0-01rel0"
[12:48:53.747] EGL vendor: ARM
[12:48:53.747] EGL client APIs: OpenGL_ES
[12:48:53.747] EGL extensions: EGL_WL_bind_wayland_display
               EGL_KHR_partial_update EGL_KHR_image_pixmap
               EGL_EXT_image_dma_buf_import EGL_KHR_config_attribs
               EGL_KHR_image EGL_KHR_image_base EGL_KHR_fence_sync
               EGL_KHR_wait_sync EGL_KHR_gl_colorspace
               EGL_KHR_get_all_proc_addresses EGL_IMG_context_priority
               EGL_ARM_pixmap_multisample_discard
               EGL_ARM_implicit_external_sync EGL_KHR_gl_texture_2D_image
               EGL_KHR_gl_renderbuffer_image EGL_KHR_create_context
               EGL_KHR_surfaceless_context EGL_KHR_gl_texture_cubemap_image
               EGL_EXT_create_context_robustness
[12:48:53.752] warning: Disabling render GPU timeline and explicit synchronization due to missing EGL_ANDROID_native_fence_sync extension
[12:48:53.753] Bad/unknown DRM format code 0x00000000.
[12:48:53.754] EGL_KHR_surfaceless_context available
[12:48:53.763] GL version: OpenGL ES 3.2 v1.r18p0-01rel0.db8fd8841edf74cef96ef24ce665edac
[12:48:53.763] GLSL version: OpenGL ES GLSL ES 3.20
[12:48:53.764] GL vendor: ARM
[12:48:53.764] GL renderer: Mali-T860
[12:48:53.764] GL extensions: GL_ARM_rgba8 GL_ARM_mali_shader_binary
               GL_OES_depth24 GL_OES_depth_texture
               GL_OES_depth_texture_cube_map GL_OES_packed_depth_stencil
               GL_OES_rgb8_rgba8 GL_EXT_read_format_bgra
               GL_OES_compressed_paletted_texture
               GL_OES_compressed_ETC1_RGB8_texture GL_OES_standard_derivatives
               GL_OES_EGL_image GL_OES_EGL_image_external
               GL_OES_EGL_image_external_essl3 GL_OES_EGL_sync
               GL_OES_texture_npot GL_OES_vertex_half_float
               GL_OES_required_internalformat GL_OES_vertex_array_object
               GL_OES_mapbuffer GL_EXT_texture_format_BGRA8888
               GL_EXT_texture_rg GL_EXT_texture_type_2_10_10_10_REV
               GL_OES_fbo_render_mipmap GL_OES_element_index_uint
               GL_EXT_shadow_samplers GL_OES_texture_compression_astc
               GL_KHR_texture_compression_astc_ldr
               GL_KHR_texture_compression_astc_hdr
               GL_KHR_texture_compression_astc_sliced_3d GL_KHR_debug
               GL_EXT_occlusion_query_boolean GL_EXT_disjoint_timer_query
               GL_EXT_blend_minmax GL_EXT_discard_framebuffer
               GL_OES_get_program_binary GL_OES_texture_3D
               GL_EXT_texture_storage GL_EXT_multisampled_render_to_texture
               GL_OES_surfaceless_context GL_OES_texture_stencil8
               GL_EXT_shader_pixel_local_storage
               GL_ARM_shader_framebuffer_fetch
               GL_ARM_shader_framebuffer_fetch_depth_stencil
               GL_ARM_mali_program_binary GL_EXT_sRGB
               GL_EXT_sRGB_write_control GL_EXT_texture_sRGB_decode
               GL_EXT_texture_sRGB_R8 GL_EXT_texture_sRGB_RG8
               GL_KHR_blend_equation_advanced
               GL_KHR_blend_equation_advanced_coherent
               GL_OES_texture_storage_multisample_2d_array
               GL_OES_shader_image_atomic GL_EXT_robustness
               GL_EXT_draw_buffers_indexed GL_OES_draw_buffers_indexed
               GL_EXT_texture_border_clamp GL_OES_texture_border_clamp
               GL_EXT_texture_cube_map_array GL_OES_texture_cube_map_array
               GL_OES_sample_variables GL_OES_sample_shading
               GL_OES_shader_multisample_interpolation GL_EXT_shader_io_blocks
               GL_OES_shader_io_blocks GL_EXT_tessellation_shader
               GL_OES_tessellation_shader GL_EXT_primitive_bounding_box
               GL_OES_primitive_bounding_box GL_EXT_geometry_shader
               GL_OES_geometry_shader GL_ANDROID_extension_pack_es31a
               GL_EXT_gpu_shader5 GL_OES_gpu_shader5 GL_EXT_texture_buffer
               GL_OES_texture_buffer GL_EXT_copy_image GL_OES_copy_image
               GL_EXT_color_buffer_half_float GL_EXT_color_buffer_float
               GL_EXT_YUV_target GL_OVR_multiview GL_OVR_multiview2
               GL_OVR_multiview_multisampled_render_to_texture
               GL_KHR_robustness GL_KHR_robust_buffer_access_behavior
               GL_EXT_draw_elements_base_vertex
               GL_OES_draw_elements_base_vertex
[12:48:53.819] GL ES 3.2 - renderer features:
               read-back format: BGRA
               EGL Wayland extension: yes
[12:48:53.820] couldn't fstat launcher tty: Bad file descriptor
[12:48:53.837] event1  - adc-keys: is tagged by udev as: Keyboard
[12:48:53.837] event1  - adc-keys: device is a keyboard
[12:48:53.838] event0  - Typec_Headphone: is tagged by udev as: Switch
[12:48:53.879] event0  - not using input device '/dev/input/event0'
[12:48:53.881] event2  - gpio-keys: is tagged by udev as: Keyboard
[12:48:53.882] event2  - gpio-keys: device is a keyboard
[12:48:53.919] libinput: configuring device "adc-keys".
[12:48:53.919] libinput: configuring device "gpio-keys".
[12:48:53.920] DRM: head 'eDP-1' updated, connector 79 is disconnected.
[12:48:53.920] DRM: head 'eDP-1' found, connector 79 is disconnected.
[12:48:53.921] DRM: head 'DP-1' updated, connector 81 is disconnected.
[12:48:53.921] DRM: head 'DP-1' found, connector 81 is disconnected.
[12:48:53.950] DRM: head 'HDMI-A-1' updated, connector 83 is connected, EDID make 'DEL', model 'DELL U2713HM', serial 'GK0KD345B46L'
[12:48:53.950] DRM: head 'HDMI-A-1' found, connector 83 is connected, EDID make 'DEL', model 'DELL U2713HM', serial 'GK0KD345B46L'
[12:48:53.952] Registered plugin API 'weston_drm_output_api_v1' of size 24
[12:48:53.952] Color manager: no-op
[12:48:53.952] Output 'HDMI-A-1' using color profile: built-in default sRGB SDR profile
[12:48:53.953] Chosen EGL config details: id:   9 rgba: 8 8 8 0 buf: 24 dep:  0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[12:48:53.954] Output HDMI-A-1 (crtc 67) video modes:
               1920x1080@60.0, preferred, current, 148.5 MHz
               1920x1080@59.9 16:9, 148.4 MHz
               1920x1080i@60.0, 74.2 MHz
               1920x1080i@60.0 16:9, 74.2 MHz
               1920x1080i@59.9 16:9, 74.2 MHz
               1920x1080@50.0 16:9, 148.5 MHz
               1920x1080i@50.0 16:9, 74.2 MHz
               1920x1080@24.0 16:9, 74.2 MHz
               1600x1200@60.0, 162.0 MHz
               1680x1050@59.9, 119.0 MHz
               1280x1024@75.0, 135.0 MHz
               1280x1024@60.0, 108.0 MHz
               1280x800@59.9, 71.0 MHz
               1152x864@75.0, 108.0 MHz
               1280x720@60.0, 74.2 MHz
               1280x720@60.0 16:9, 74.2 MHz
               1280x720@59.9 16:9, 74.2 MHz
               1280x720@50.0 16:9, 74.2 MHz
               1024x768@75.0, 78.8 MHz
               1024x768@60.0, 65.0 MHz
               800x600@75.0, 49.5 MHz
               800x600@60.3, 40.0 MHz
               720x576@50.0 4:3, 27.0 MHz
               720x576@50.0 16:9, 27.0 MHz
               720x576i@50.0 16:9, 13.5 MHz
               720x576i@50.0 4:3, 13.5 MHz
               720x480@60.0 4:3, 27.0 MHz
               720x480@60.0 16:9, 27.0 MHz
               720x480@59.9, 27.0 MHz
               720x480@59.9 16:9, 27.0 MHz
               720x480@59.9 4:3, 27.0 MHz
               720x480i@60.0 16:9, 13.5 MHz
               720x480i@60.0 4:3, 13.5 MHz
               720x480i@59.9 16:9, 13.5 MHz
               720x480i@59.9 4:3, 13.5 MHz
               640x480@75.0, 31.5 MHz
               640x480@60.0 4:3, 25.2 MHz
               640x480@59.9, 25.2 MHz
               640x480@59.9 4:3, 25.2 MHz
               720x400@70.1, 28.3 MHz
[12:48:53.967] associating input device event1 with output HDMI-A-1 (none by udev)
[12:48:53.968] associating input device event2 with output HDMI-A-1 (none by udev)
[12:48:53.969] Output 'HDMI-A-1' enabled with head(s) HDMI-A-1
[12:48:53.969] Compositor capabilities:
               arbitrary surface rotation: yes
               screen capture uses y-flip: yes
               cursor planes: yes
               arbitrary resolutions: no
               view mask clipping: yes
               explicit sync: no
               color operations: no
               presentation clock: CLOCK_MONOTONIC, id 1
               presentation clock resolution: 0.000000001 s
[12:48:53.974] Loading module '/usr/lib/weston/desktop-shell.so'
[12:48:53.976] launching '/usr/libexec/weston-keyboard'
[12:48:53.978] Note: support for the deprecated wl_shell interface is disabled. If a legacy client still needs it, it can be re-enabled by passing -Ddeprecated-wl-shell=true to Meson when building Weston.
[12:48:53.979] launching '/usr/libexec/weston-desktop-shell'
could not load cursor 'dnd-move'
could not load cursor 'dnd-move'
could not load cursor 'dnd-copy'
could not load cursor 'dnd-copy'
could not load cursor 'dnd-none'
could not load cursor 'dnd-none'
QStandardPaths: runtime directory '/var/run' is not a directory, but a symbolic link to a directory permissions 0755 owned by UID 0 GID 0
QLauncher available size : 1920 x 1080
arm_release_ver of this libmali is 'r18p0-01rel0', rk_so_ver is '5'.
rga_api version 1.3.1_[11] (RGA is compiling with meson base: $PRODUCT_BASE)
xkbcommon: ERROR: couldn't find a Compose file for locale "zh_CN.utf8"
could not create XKB compose table for locale 'zh_CN.utf8'.  Disabiling compose
xkbcommon: ERROR: couldn't find a Compose file for locale "zh_CN.utf8"
could not create XKB compose table for locale 'zh_CN.utf8'.  Disabiling compose
[12:49:00.013] Warning: computed repaint delay is insane: -4011 msec
